Command-line Tools and C library for blink(1) USB RGB LED

This is an official collection of C/C++ commandline tools for controlling the blink1 USB RGB LED.

This code lives at https://github.com/todbot/blink1-tool.

For pre-built binaries, see the Releases page.

The current tools are:

• blink1-tool -- command-line tool for controlling blink(1)
• blink1-tiny-server -- Simple HTTP JSON API server to control blink(1) (README)
• blink1control-tool -- blink1-tool for use with Blink1Control (uses HTTP REST API)
• blink1-lib -- C library for controlling blink(1)
• blink1-mini-tool -- commandline tool using libusb-0.1 and minimal deps, for older systems
• blink1raw -- small example commandline tool using Linux hidraw

Type make help for a full list.

Also see in this directory:

• scripts -- examples shell scripts using blink1-tool

Supported platforms

Supported platforms for blink1-tool and blink1-lib:

• Mac OS X 10.7+
• Windows XP+,10,11 (built with MinGW & MSYS)
• Linux (most all, primary development on Ubuntu)
• FreeBSD 8.2+
• Raspberry Pi OS / Raspian
• BeagleBone (Ubuntu)
• OpenWRT / DD-WRT
• ... just about anything else with Gnu Make & a C-compiler

In general, blink1-tool and blink1-tiny-server build as a static binaries as much as possible, requiring only basic system libraries. This eliminates the need for shared library dependencies on the target. However, static builds can be problematic for some systems with different libusb implementations, so doing make EXEFLAGS= will generally build a non-static version.

Commmand-line options for blink1-tool

% blink1-tool --help
Usage: 
  blink1-tool <cmd> [options]
where <cmd> is one of:
  --list                      List connected blink(1) devices 
  --rgb=<red>,<green>,<blue>  Fade to RGB value
  --rgb=[#]RRGGBB             Fade to RGB value, as hex color code
  --hsb=<hue>,<sat>,<bri>     Fade to HSB value
  --blink <numtimes>          Blink on/off (use --rgb to blink a color)
  --flash <numtimes>          Flash on/off (same as blink)
  --on | --white              Turn blink(1) full-on white 
  --off                       Turn blink(1) off 
  --red                       Turn blink(1) red 
  --green                     Turn blink(1) green 
  --blue                      Turn blink(1) blue 
  --cyan                      Turn blink(1) cyan (green + blue) 
  --magenta                   Turn blink(1) magenta (red + blue) 
  --yellow                    Turn blink(1) yellow (red + green) 
  --lastcolor, --rgbread      Read last RGB color sent (post gamma-correction)
  --setpattline <pos>         Write pattern RGB val at pos (--rgb/hsb to set)
  --getpattline <pos>         Read pattern RGB value at pos
  --savepattern               Save RAM color pattern to flash (mk2+)
  --clearpattern              Erase color pattern completely 
  --play <1/0,pos>            Start playing color pattern (at pos)
  --play <1/0,start,end,cnt>  Play color pattern sub-loop (mk2+)
  --playstate                 Return current status of pattern playing (mk2+)
  --playpattern <patternstr>  Play Blink1Control pattern string in blink1-tool
  --writepattern <patternstr> Write Blink1Control pattern string to blink(1)
  --readpattern               Download full blink(1) patt as Blink1Control str
  --servertickle <1/0>[,1/0,start,end] Turn on/off servertickle (w/on/off, uses -t msec)
  --chase, --chase=<num,start,stop> Multi-LED chase effect. <num>=0 runs forever
  --random, --random=<num>    Flash a number of random colors, num=1 if omitted 
  --glimmer, --glimmer=<num>  Glimmer a color with --rgb (num times)
 Nerd functions: 
  --fwversion                 Display blink(1) firmware version 
  --version                   Display blink1-tool version info 
  --setstartup                Set startup parameters (v206+,mk3) 
  --getstartup                Get startup parameters (v206+,mk3) 
  --gobootload                Enable bootloader (mk3 only)
  --lockbootload              Lock bootloader (mk3 only)
  --getid                     Get unique id (mk3 only)
and [options] are: 
  -d dNums --id all|deviceIds Use these blink(1) ids (from --list) 
  -g -nogamma                 Disable autogamma correction
  -b b --brightness b         Set brightness (0=use real vals, 1-255 scaled)
  -m ms,   --millis=millis    Set millisecs for color fading (default 300)
  -q, --quiet                 Mutes all stdout output (supercedes --verbose)
  -t ms,   --delay=millis     Set millisecs between events (default 500)
  -l <led>, --led=<led>       Which LED to use, 0=all/1=top/2=bottom (mk2+)
  --ledn 1,3,5,7              Specify a list of LEDs to light
  -v, --verbose               verbose debugging msgs

Examples: 
  blink1-tool -m 100 --rgb=255,0,255    # Fade to #FF00FF in 0.1 seconds 
  blink1-tool -t 2000 --random=100      # Every 2 seconds new random color
  blink1-tool --led 2 --random=100      # Random colors on both LEDs 
  blink1-tool --rgb 0xff,0x00,0x00 --blink 3  # blink red 3 times
  blink1-tool --rgb '#FF9900'           # Make blink1 pumpkin orange
  blink1-tool --rgb FF9900 --led 2      # Make blink1 orange on lower LED
  blink1-tool --chase=5,3,18            # Chase pattern 5 times, on leds 3-18

Pattern Examples: 
  # Play purple-green flash 10 times (pattern runs in blink1-tool so blocks)
  blink1-tool --playpattern '10,#ff00ff,0.1,0,#00ff00,0.1,0'
  # Change the 2nd color pattern line to #112233 with a 0.5 sec fade
  blink1-tool -m 500 --rgb 112233 --setpattline 1 
  # Erase all lines of the color pattern and save to flash 
  blink1-tool --clearpattern ; blink1-tool --savepattern 

Servertickle Examples: 
  # Enable servertickle to play pattern after 2 seconds 
  # (Keep issuing this command within 2 seconds to prevent it firing)
  blink1-tool -t 2000 --servertickle 1 
  # Enable servertickle after 2 seconds, play sub-pattern 2-3 
  blink1-tool -t 2000 --servertickle 1,1,2,3 

Setting Startup Params Examples (mk2 v206+ & mk3 only):
  blink1-tool --setstartup 1,5,7,10  # enable, play 5-7 loop 10 times
  blink1-tool --savepattern          # must do this to save to flash 

User notes (mk3 only):
  blink1-tool --writenote 1 --notestr 'hello there' 
  blink1-tool --readnote 1 
  blink1-tool --readnotes    # reads all notes out 


Notes: 
 - To blink a color with specific timing, specify 'blink' command last:
   blink1-tool -t 200 -m 100 --rgb ff00ff --blink 5 
 - If using several blink(1)s, use '-d all' or '-d 0,2' to select 1st,3rd: 
   blink1-tool -d all -t 50 -m 50 -rgb 00ff00 --blink 10 

OS-specific Notes

Linux (including Raspberry Pi)

To use blink(1) as a non-root user, udev rules must be installed. On Debian-like systems (Ubuntu, Raspian), these udev rules are installed with:

sudo cp 51-blink1.rules /etc/udev/rules.d/51-blink1.rules
sudo udevadm control --reload
sudo udevadm trigger

Building from source

In general you can do:

git clone https://github.com/todbot/blink1-tool
cd blink1-tool
make

On Linux you will need to install some requirements beforehand.

If your OS is not detected automatically, you can force it with something like:

OS=linux make

To see the supported platforms, please consult the Makefile

Build variants

There are two primary USB libraries that blink1-tool can be built for:

• USBLIB_TYPE=HIDAPI -- Uses the feature-rich cross-platform hidapi library (default)
• USBLIB_TYPE=HIDDATA -- Uses a simple, cross-platform hiddata library (included)

For Linux, there are to HIDAPI_TYPEs you can choose from:

• HIDAPI_TYPE=HIDRAW -- Uses standard hidraw kernel API for HID devices (default)
• HIDAPI_TYPE=LIBUSB -- Uses lower-level libusb commands (good for older Linuxes)

To compile for a particular USBLIB_TYPE or HIDAPI_TYPE, specify them when buildling:

HIDAPI_TYPE=LIBUSB make

OS-specific prerequisites for compiling

If you have the ability to compile programs on your system, you may already have everything you need to compile blink1-tool.

Linux (Debian-flavored, including Raspberry Pi)

• In a terminal, install pre-reqs and build:

  sudo apt install build-essential git pkg-config libudev-dev
  sudo apt install libusb-1.0-0-dev  # (optional, only for libusb variant)
  cd blink1-tool
  make blink1-tool
  make blink1-tiny-server
  HIDAPI_TYPE=libusb make blink1-tool # (if you instead you want libusb version)

FreeBSD

• Install pre-reqs and build:

  sudo pkg install gmake gcc git libiconv
  cd blink1-tool
  gmake`
  sudo ./blink1-tool --red --flash 3

If you'd like devd support, see the devd-51-blink1.conf file.

MacOS

• Xcode

• In Terminal, setup Xcode and build:

  xcode-select --install
  cd blink1-tool
  make blink1-tool

Windows

• Install Visual Studio 2017 or 2019
• Install MSYS2: https://www.msys2.org/
• In MSYS2 bash shell:

  pacman -S base-devel make git zip unzip mingw-w64-x86_64-gcc
  export PATH=${PATH}:/c/msys64/mingw64/bin
  export PATH=${PATH}:"/c/Program Files (x86)/Microsoft Visual Studio 14.0/VC/bin"
  export PATH=${PATH}:'/c/Program Files (x86)/Microsoft Visual Studio/2019/BuildTools/VC/Tools/MSVC/14.29.30133/bin/Hostx64/x64'"
  make
  

Other OSes

See the blink1-tool/Makefile for details

Using blink1-lib in your C/C++ project

See Makefile for your platform

Docker and blink(1)

To build a image from Dockerfile-ubuntu:

• docker build -f Dockerfile-ubuntu -t todbot/blink1 .

Running the container:

• blink1-tool:

  • docker run --rm -it --privileged todbot/blink1 blink1-tool --on
  • docker run --rm -it --device /dev/bus/usb:/dev/bus/usb todbot/blink1 blink1-tool --on

• blink1-tiny-server:

  • docker run -d -p 8934:8934 --privileged todbot/blink1 blink1-tiny-server --host 0.0.0.0 -p 8934

Note the --privileged tag, docker needs this to access the hosts USB controllers. You can also specify a specific USB device with something like --device=/dev/bus/usb/003/003

Docker resources

• Install Guide
• Run Command
• Ubuntu Dockerfile